NanoVNA-H Features:

✅ New Upgraded Version: Compared with old version NanoVNA, it added of ABS casing and the new packaging. Hot stamping technology and plastic inner protection reduce the problems caused by transportation shocks and other processes. Support time domain analysis function (TDR).

✅ USB-C to USB-C: Support USB-C to USB-C line, more convenient to connect to mobile phones. Compatible with most Android phones with the same screen display (doesnt support for iPhone). Solve the problem of small screen, insufficient brightness and so on. Besides, the battery usage can be displayed on the interface.

✅ Wide Range Frequency: The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The metal shield is designed to reduce the external interference and improve the measurement accuracy. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics

✅ Unit is designed to Original Equipment (OE) fit, form and function Simple and practical PC control software, you can export Touchstone (snp) files for various radio design and simulation software through PC software. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, please manually replace the transceiver port wiring. Other details have been improved.

✅ Equirements accomplished by leveraging Spectra Premiums OE engine management systems design expertise.Platinum connector threads reduce the number of connection points for faster reaction to change. Ceramic-built printed circuit boards are protected by silica gel, providing superior resistance to temperature changes and vehicle vibrations.

Specification:
- PCB: 54mm x 85.5mm x 11mm (without the size of connectors, switches)
- Measurement Frequency: 10KHz -1.5GHz
- RF Output: -13dbm (maximum -9dbm)
- Frequency Accuracy: ＜0.5ppm
- Measurement Range: 70dB (50kHz-300MHz), 50dB (300M-600MHz), 40dB (600M-900MHz) enable extended firmware)
- Port SWR: < 1.1
- Display: 2.8 inch TFT (320 x240)
- USB Interface: USB Type-C; Communications Mode: CDC (Serial)
- Power Supply: USB 5V 120mA, built-in 650mAh electricity, maximum charging current 0.8A
- Number of Calibration Points: 101 (Fixed)
- Number of Scanning Points: 101 (Fixed)
- Display Tracking: 4, Marking: 4, Save Setting : 5
- Measuring S parameters, voltage standing wave ratio, phase, delay, Smith chart and the like

New Upgraded Latest Version 3.6 Vector Network Antenna Analyzer 10KHz-1.5GHz MF HF VHF UHF with Shell

ABS case: 58.7mm x 91.3mm x 17.1mm (excluding protrusions)

PCB: 54mm x 85.5mm x 11mm (without connectors, switches)

Measurement frequency: 10KHz -1.5GHz

RF output: 0dbm (±2dbm)

Measurement range: 70dB (50kHz-300MHz), 60dB (300M-900MHz), 40dB(0.9G-1.5GHz));

Port SWR: < 1.1

Display: 2.8 inch TFT (320 x240)

USB interface: USB type-C communication mode: CDC (serial)

Power: USB 5V 120mA, built-in 650mA-h battery, maximum charging current 300mA

Number of scanning points: 101 (fixed)

Display Tracking: 4, Marking: 4, Setting Save: 5

Frequency Tolerance:<2.5ppm

Frequency Stability:<0.5ppm

Saving Measurement Data with a MicroSD Card—Support up to 32GB Memory Card

You can use a MicroSD card to save measurement data in SNP format or to save screenshots in BMP format. MicroSD card uses SPI mode and only supports smaller than 32GB and formatted with FAT or FAT32.

In addition, different from old version, the date and time of vna can be display, which is convenient for you to further record and save data.

 

What can you get?

1X Antenna Analyzer Host

2X 20cm SMA Male to Male RG174 RF Cable

2X SMA Female to Female Connector

1X SMA Simple Calibration Kit SHORT

1X SMA Simple Calibration kit OPEN

1X SMA Simple Calibration kit LOAD

1X USB Type-C Data Cable

1X USB-C to USB-C Line

1X Touch Paddle

HF VHF UHF Antenna Analyzer Measuring

New Upgraded Version

The default firmware main function is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring

• - Measuring S parameters, voltage standing wave ratio, phase, delay, Smith chart and the like
• - Built-in 650mA-h Battery,you can connect the vector network analyzer to your PC for a large screen display with a USB-C cable. The working time is above 3 hours.
• - The SWR readings is accurate for tuning antennas with a frequency range of 50kHz to 900MHz. Smith chart will help you to determine reactance and resistance for an antenna.
• - Saving Measurement Data with a MicroSD Card—Support up to 32GB Memory Card
• - The 2.8inch Touch Screen Vector Network Analyzer Kit could be protected with a ABS shell. Preventing damage to parts. And save your printing money.
• - It's very useful as an antenna analyzer for your ham station. Equipped with an open and short and load for calibrating it as well as some cables. Ideal for every ham radio user.

 

Support Android Phone & PC Software Control

Compare with old version, it supports time domain analysis function (TDR), and more convenient to connect to mobile phones. Compatible with most Android mobile phones. Support Windows Computer Control.